Nieuws nl

February 2012 -
The WENZEL ONYX IV is a small lightweight ruggedized OCXO featuring low phase noise (-165 dBc/Hz, standard), good temperature stability and low g-sensitivity (to <3E-10/g, typical). Designed for military PCB mount applications to provide excellent phase noise performance during vibration.
The nickel-plated steel package is only 1″ x 1″ x 0.5″ to house this full featured oscillator, which also includes an internal volrtage regulator to provide excellent power supply line rejection.
Please consult us if you need any specifications to be modified to better suit your application.                                                                                          

New Product Introduction          “SECOND GENERATION TO-8 OSCILLATORS” MLTO-Series“TO-8” low noise YIG-Tuned Oscillators covering up to 13 GHz: Micro Lambda Wireless, Inc. announces the production release of second generation TO-8 PC Board compatible YIG-Tuned oscillators covering 2 to 13 GHz. Utilizing new permanent magnets and SiGe transistors, these units are available in a standard package size of .500” tall. All units have a .675” diameter cylinder package. They provide +10 dBm power output levels and operate over the 0 to +65 C commercial temperature ranges. Extended temperature models to +85 C are available for all models. Phase noise performance of -98 to -100 dBc/Hz at 10 kHz offset and -123 to -128 dBc/Hz at 100 kHz offset are guaranteed for all model types depending on frequency Applications include Analyzers, Generators, Receivers, and Frequency Synthesizers. pdf

                                                                                                                  
                                                                                                                 
                                                                                                                                                                     
- Effective immediately at no additional cost, the HAMEG 1 GHz Spectrum Analyzers HMS1000/1010 are also available with a RBW (Resolution Bandwidth) of 100Hz, improving the DANL (Displayed Average Noise Level) as a result. The specifications of the 1GHz and the 3GHz instruments now only differ by the input frequency range. Owners of older instruments don’t miss out either; they can upgrade their instruments to the new firmware version so they will equal new instruments as far as the parameters are concerned.

- A new Reference for the entry into Spectrum Analysis … Owing to their slogan ‘Great Value in Test & Measurement’ HAMEG present the new HMS1000E which is available from stock (Item Number 22-1000-E000). It is the proper successor to the HM5510. It is an economy version based on the modern platform of the HMS series, with considerably more functions (RBW, VBW, markers…) than its predecessor.

    
Micro Lambda Wireless Inc. MLBF-Series CE Certified !
The MLBF-Series Bench test filters are ideal for production test sets, laboratory tests and test equipment racks where filtering of microwave signals is essential. These bench top filter assemblies provide either Bandpass or Bandreject (notch) filter types depending on application. Frequency coverage is dependent on which production filter type is chosen. Frequency coverage for Bandpass models range from 500 MHz to 50 GHz while the Bandreject models cover 500 MHz to 20 GHz. Each bench top filter assembly consists of a YIG-Tuned filter chosen by the user, Heat sink, compensated driver, power supply, cooling fans, keyboard, display, USB interface, Ethernet interface and a manual tuning knob. Components are housed in a 10” wide, 4” height, 13” deep enclosure with mounting feet and handle.

[The MSO for the broader market ...]
The highly successful HMO series have been extended. While, up until now, only instruments from 250…350MHz were offered at prices above € 3,000, HAMEG has also addressed the range from 70…200MHz.
Eight new oscilloscopes have been been presented in March 2011. The 4 channel, 70 and 100MHz instruments is available since the end of May, with the other models to follow in July. In terms of the operation and the front panel interface, the new instruments hardly differ from the existing HMO series products. A Component Tester was added which is highly appreciated in this class. Using the known option HO3508 allows for eight digital channels to be analyzed. The I2C, SPI and UART/RS-232 trigger and decode option HOO11 (licence key) is new; in the first year of introduction, it will be delivered with the instruments free of charge.
Hence even with the 2 channel instrument, an I2C, SSPI and UART/RS-232 signal can be analyzed without any additional accessories.
For the 3-wire SPI bus the 2 channel instrument requires just one additional probe for the external trigger input.
The new HMO’s are only 140 mm deep and may be stacked – as to be expected – on every other HAMEG instrument.
                                                                      

                                          
                                                                                                                        

                                                                                 
                                                                                
 

Obsolescence announcement !!
After 40 years in production, Kaman Precision Products is announcing the obsolescence of the KD-2300 product. Many circumstances have contributed to this decision, component obsolescence being the biggest driver. The replacement product, the KD-2306, has been in production since 2007 and has proven to be a very worthy improvement of what was certainly the benchmark for all non-contact inductive displacement sensors. Key dates to remember are: Effective immediately, Kaman will no longer sell the KD-2300 into new applications. December 31, 2011, all sales of the KD-2300 will cease. December 31, 2014, Kaman will no longer support the KD-2300 product with service/repair. The new version of the old benchmark offers higher gain voltage output, as well as 4-20 mA output. It is housed in a convenient DIN rail mount enclosure and is CE marked as well as being RoHS compliant. The KD-2306 is offered with all the sensor models that were available with the KD-2300. Click here for the new KD-2306 product brochure.                                  
                                                                            
                                                                     
                                                                                   
                                                                                                                                            
                                                                                                                                                            

 

FuG Elektronik introduces Medium- and High Voltage Power Supplies from 5 to 15 kW with new design.
As of now, middle and high voltage power supplies with max. output voltages from 125V to 12,500V available in the power classes 5, 10 and 15 kW in a desktop case of 6 to 12 U height. Such units were previously available only in our HCH series. With the new design of the MCP and HCP power supplies of the related voltage and power it was possible to reduce dimensions and weight by approximately half. Due to reduced manufacturing costs associated with the reduction of dimensions and weight the devices can be offered at attractive prices!
                                                                                         

                                                                         
                                                                        
                                                                       
                                                                         
                                                                       
                                                                      
                                                                      

The new ClareHAL 104 takes the features of previous ClareHAL versions and combines them into one easy unit. The ClareHAL 104 truly is the one size fits all solution – combined with results storage! The simple intuitive user interface enables easy push-button manual testing, alternatively the full power of this unique instrument can be used to automate the testing sequence for fast performance on the most demanding production lines.
Tests can be started and stopped by simply pushing the large buttons on the front of the instrument or choose from a variety of pre-selected automated configurations, including remote PC’s, PLC’s or interlocks. The ClareHAL’s internal memory will store up to 6000 test results and can be interfaced with a variety of accessories ranging from barcode scanners through to label printers.

Features:
 Earth / Ground Bond Testing.
 AC Flash / HIPOT Testing (Dielectric Withstand Testing).
 DC Flash / HIPOT Testing.
 DC Insulation Resistance Testing.
 ARC Detection.
 Leakage Testing.
 Load Power Testing. Power Factor.
 Results Memory.
 Automation Option.
 Scanner / Printer Option.

01-02-2012